Defence Tech solutions for FPV UAVs – Electronics, Constructions, 3D design, Development & Manufacturing
OUR PRODUCTS
FPV KAMIKAZE 10" ▽
Takeoff weight up to 8 kg
Payload weight up to 5 kg
Flight time with payload up to 17 minutes
Tactical range up to 20 km
Altitude up to 500 m
Maximum speed up to 120 km/h
Control: ELRS or MILELRS 433 MHz
Video transmitter: 2.5 W, 5.0–5.9 GHz, analog
Price with 6S4P battery: 620 USD
FPV BOMBER 8" ▽
Takeoff weight up to 3.5 kg
Payload weight up to 2 kg
Flight time with payload up to 17 minutes
Tactical range up to 10 km
Altitude up to 500 m
Maximum speed up to 120 km/h
Control: ELRS or MILELRS 433 MHz
Video transmitter: 2.5 W, 5.0–5.9 GHz, analog
Price with 6S2P battery: 500 USD
MACHINE VISION FPV COPILOT ▽
Increases the number of successful FPV strikes by avoiding radio interference and operator errors
“Device-in-the-middle” connection. Easy integration between FPV camera and flight controller, as well as between receiver and controller
Target lock on lightly armored vehicles – up to 200 m
Target lock on human figure – up to 50 m
Once the target is locked, the COPILOT controls the drone
Functions: zoom, target release
Price: 190 USD
FLIGHT CONTROLLER F405 WING
Microcontroller: STM32F405
Gyroscope and accelerometer: ICM-42688-P
Barometer: MS561101BA03-50
Blackbox: TF/microSD card slot
OSD: AT7456E
Input voltage: 3–8S
Built-in BEC: 5 V 2 A DC converter for powering various peripherals
Peripheral connection via JST GHS connectors (compatible plugs on cables should be JST GHR-0XV-S or similar)
6 UART ports
1 I2C port
10 signal outputs for servos/motors
Signal inverter on UART2 RX for non-inverted SBUS receivers
Voltage sensor and current sensor input
SWDIO and SWCLK pads for direct programming (e.g. via ST-Link)
Board dimensions: 38×56 mm
Mounting hole spacing: 30.6×30.6 mm
Price: 45 USD
FLIGHT CONTROLLER F405 RE
Microcontroller: STM32F405
Gyroscope and accelerometer: BMI270
Barometer: DPS310
OSD: AT7456E
Target: SpeedyBee F405 V3
Supported firmware: BetaFlight, iNav, Ardupilot
Input voltage: 3–6S
Built-in BEC – DC converter 5 V 2 A + 9 V 2 A, supports powerful peripherals such as AKK Ultralong Range transmitters and drop servos
Peripheral connection via JST GHS connectors (compatible plugs on cables should be JST GHR-0XV-S or equivalent)
5 UART ports, 1 I2C port
9 signal outputs for servos/motors
Signal inverter on UART2 RX for non-inverted SBUS receivers
Voltage sensor and current sensor input
Board dimensions: 40×42 mm
Mounting hole spacing: 30.6×30.6 mm
Price: 30 USD
ELECTRONIC SPEED CONTROLLER BLS80A RE 8S
Microcontroller: EFM8BB21
Type: BLHELI_S
Target: J-H-50
Supported firmware: Blheli_S, Bluejay
Input voltage: 3–8S LiPo/LiIon
Maximum motor current: 80 A
Connector: JST SM08B-SRSS-TB
Matching plug: JST SHR-08V-S-B series
Power cable mounting holes: 10 AWG
Mounting hole spacing: 30.6×30.6 mm
Price: 60 USD
ELECTRONIC SPEED CONTROLLER BLS50A RE 6S
Microcontroller: EFM8BB21
Type: BLHELI_S
Target: J-H-50
Supported firmware: Blheli_S, Bluejay
Input voltage: 3–6S LiPo/LiIon
Maximum motor current: 50 A
Connector: JST SM08B-SRSS-TB
Matching plug: JST SHR-08V-S-B series
Power cable mounting holes: 12 AWG
Mounting hole spacing: 30.6×30.6 mm
Price: 35 USD
RECEIVER ELRS24900 XG XROSSBAND GEMINI
Frequency Range: 862 - 1020 MHz + 2.4 - 2.5 GHz
Chipset: LR1121 x2 + ESP32
Target: Radiomaster XR4
Firmware Version: 3.5.6
MILELRS Support: Yes, can be set as default
Supported Output Protocols: CRSF, inverted CRSF, SBUS, inverted SBUS, SUMD, DJI RS2 Pro
Telemetry Transmit Power: up to 150 mW
Operating Voltage: 3.6 V - 6.0 V
Antenna Connector Type: IPEX1 (uFl)
Signal Connector Type: PLS-4 (solder pad) + SM04B-GHS-TB
Receiver Weight: 2.5 g (without antenna)
Dimensions: 20 × 30 × 7 mm
Price: 33 USD
RECEIVER ELRS900 DX DIVERSITY GEMINY
Frequency range: 720 – 1020 MHz
Chips: 2× SX1276 + ESP32
Target: BetaFPV 900RX
Firmware version: 3.5.1
MILELRS support: yes (can be preinstalled)
Supported output protocols: CRSF, inverted CRSF, SBUS, inverted SBUS, SUMD, DJI RS2 Pro
Telemetry transmitter power: up to 50 mW
Input voltage: 3.6 V – 5.5 V
Antenna connector type: IPEX1 (uFl)
Signal connector type: PLS-4 (for soldering) + SM04B-GHS-TB
Receiver weight: 0.6 g (without antenna)
Dimensions: 20×30 mm
Price: 29 USD
RECEIVER ELRS433
Frequency range: 410 – 530 MHz
Target: BetaFPV 900RX or proprietary LT (for FHSS firmware)
Firmware version: 3.5.1
MILELRS support: yes (can be preinstalled)
Supported output protocols: CRSF, inverted CRSF, SBUS, inverted SBUS, SUMD, DJI RS2 Pro
Telemetry transmitter power: up to 50 mW
Input voltage: 4 V – 6 V
Antenna connector type: IPEX1 (uFl)
Signal connector type: PLS-4 (for soldering)
Dimensions: 23×33 mm
Price: 15 USD
TRANSMITTER ELRS433 1W/2W JR
Communication system: ELRS
Support for other communication systems: Yes — MILELRS, BANDERA, BARVINOK
Frequency range: 410 – 530 MHz
Communication system: ELRS
Output power: 1 W / 2 W max (depending on version)
Input voltage: 7 – 30 V
Active cooling system: yes
RF connector type: SMA Female
Form factor: compatible with standard JR module
Price for 1 W version: 60 USD Price for 2 W version: 70 USD
DRONE PAYLOAD DROP SYSTEM FOR FPV
Features: Equipped with a special mounting plate for drone frames based on the Picatinny rail principle. Custom plates available for any frame.
Maximum payload weight: 2 kg
Device weight with mounting plate: 61 g
Input voltage: 5 V, 0.2 A
Operating temperature range: from -5 to +40 °C
Control system interface: standard Servo PWM, 2 ms – open, 1 ms – closed
Dimensions: 57×80×33 mm
Price: 15 USD
FPV CAMERA GIMBAL
Features: Allows tilting the FPV camera downward for executing specific drone maneuvers, such as targeting for payload drop or landing in difficult conditions.
Camera mount size: 19×19 mm (micro-size cameras)
Device weight with camera: 33 g
Input voltage: 5 V, 0.2 A
Operating temperature range: from -5 to +40 °C
Control system interface: standard Servo PWM, 2 ms – camera tilt 10° above horizontal, 1 ms – vertical downward
Dimensions: 33×41×57 mm (H×W×D)
Price: 17 USD
FPV THERMAL CAMERA GIMBAL
Features: Allows tilting the FPV camera downward for executing specific drone maneuvers, such as targeting for payload drop or landing in difficult conditions.
Camera mount size: 21×21 mm (thermal camera like HM-TM53-10RG/UT model).
Device weight without camera: 25 g
Input voltage: 5 V, 0.2 A
Operating temperature range: from -5 to +40 °C
Control system interface: standard Servo PWM, 2 ms – camera tilt 10° above horizontal, 1 ms – vertical downward
Dimensions: 33×41×57 mm (H×W×D)
Price: 17 USD
FPV VTX COLOVERLEAF ANTENNA
Type: omnidirectional circularly polarized antenna of "cloverleaf" type
Center frequency: 5.8 GHz
Polarization: right-hand (RHCP); left-hand (LHCP) available on request
VSWR at center frequency: approximately 1.1
Bandwidth at VSWR ≤ 1.8: 5.1 – 6.0 GHz
Cable type: RG402
Cable length: 160 mm (custom length available on request)
Connector type: SMA (RP-SMA available on request)
Active element material: silver-plated copper
Radiation pattern: spherical
Price: 8 USD
FPV RX HELICAL ANTENNA 5.8 GHz
Type: directional circularly polarized helical antenna
Center frequency: 5.8 GHz
Polarization: right-hand (RHCP); left-hand (LHCP) available on request
Gain: 10.9 dBi
Number of turns: 8
VSWR at center frequency: approximately 1.1
Bandwidth at VSWR ≤ 1.8: 4.9 – 6.1 GHz
Connector type: SMA-Female
Active element material: silver-plated copper
Radiation pattern: forward-focused
Beamwidth: 37°
Dimensions: 104×49×47 mm
Mounting hole spacing: 38×40 mm (compatible with patch antennas by Scream Industries and Sakura)
Price: 24 USD
FPV HELICAL ANTENNA 2.4 GHz
Type: directional circularly polarized helical antenna
Center frequency: 2.4 GHz
Polarization: right-hand RHCP (left-hand LHCP available on request)
Gain: 10 dBi
Number of turns: 7
VSWR at center frequency: approximately 1.05
Frequency range at VSWR 1.8: 2.0 – 2.8 GHz
Connector type: SMA-Female
Active element material: copper
Radiation pattern: forward-stretched
Beam angle: 40°
Dimensions: 310 × 105 mm
Maximum pillar diameter: 30 mm
Price: 75 USD
10" INCH DRONE FRAME
Easy to assemble, no additional gluing required. The design is optimized for vibration and load distribution.
Maximum takeoff weight: up to 8 kg
Frame material: carbon fiber
Arm thickness: 6 mm
Plate thickness: 3 mm
Motor-to-motor distance: 310 mm
Geometry: fully symmetrical “true X” layout
Price: 55 USD
Contact Us
Contact LEADER Tech to learn more about cooperation in unmanned aerial technology.
Our Contact via QR Code
Scan or tap to reach us via WhatsApp.
© 2022 - 2026 LEADER Tech | Glory to Ukraine! Glory to the Heroes!
×
❮
❯
